• v0.1.46 042de50a88

    WarpAxe v0.1.46
    All checks were successful
    CI / Rust checks (push) Successful in 2m8s
    CI / Regulator scenarios (push) Successful in 59s
    Stable

    dvb-projekt released this 2026-11-18 13:42:56 +00:00 | 19 commits to main since this release

    IPv6 for pool connections, drivers you can reuse, and a fan PWM fix on the Nerd boards. A miner on a network with IPv6 now reaches pools that offer it over IPv6, with IPv4 at most a quarter second behind; on a network without IPv6 the only change is that the first pool connection after joining Wi-Fi waits up to 4 seconds for an IPv6 address. Several of WarpAxe's hardware drivers now live in their own crate under MIT/Apache, so other firmware can use them, and all drivers use embedded-hal 1.0. The EMC2101 (Bitaxe Gamma and Gamma Duo, NerdAxe Gamma and Gaia, BitForge Nano) now runs on the community crate emc2101-rs. Rewriting the EMC2302 driver from its datasheet turned up a wrong bit position inherited from NerdOS: on the Nerd boards the main fan now gets the 19.53 kHz PWM that was always intended, instead of 4.88 kHz. A miner that runs without trouble mines as before.

    New.

    • IPv6 for pool connections. The miner takes an IPv6 address from the router, and a pool that has both an IPv6 and an IPv4 address is tried over IPv6 first, with IPv4 starting a quarter second later if IPv6 has not answered by then, or at once if it was refused (Happy Eyeballs, RFC 8305); whichever answers first is used. A pool whose IPv6 does not answer costs a quarter second, not a timeout. A pool address may be an IPv6 literal, with or without brackets. A switch on the Network page turns it off (on by default); under it the miner's IPv6 addresses, and the pool cards show whether the connection runs over IPv4 or IPv6. Over IPv6 the web UI and API answer only the local network (the link, unique-local addresses and the miner's own /64): a global IPv6 address has no NAT in front of it. Tested on a Bitaxe Gamma on a native dual-stack line with dual-stack and IPv4-only pools, a pool whose IPv6 refuses connections, TLS over both, Stratum V2 over IPv6, and IPv6 literals and local names; a route that drops IPv6 silently is not tested on hardware. API: ipv6, ipv6Addresses, poolAddress, poolAddressFamily, ipv6Refused. Details in docs/17.
    • Note on IPv6 and privacy. The miner's IPv6 address is built from its MAC (lwIP has no privacy addresses), so IPv6 pools see the MAC. Turn the switch off if you mind.

    Changed.

    • Nerd boards: main fan PWM at 19.53 kHz. On the NerdQAxe++, NerdOctaxe and the other boards with the EMC2302 fan controller, the fan on the ASIC cooler ran at 4.88 kHz; the setting meant 19.53 kHz for both fan outputs, but put the second output's bits one place too far (EMC2302 datasheet, register 6-10). Measured on a NerdQAxe++ before and after: the same speed at 100 % (2820 / 2818 rpm) and at 25 % (790 / 791 rpm), and the fan control holds the chip at its target as before. Reported to NerdOS (shufps/ESP-Miner-NerdQAxePlus#767).
    • EMC2101 through emc2101-rs. On the Bitaxe Gamma and Gamma Duo, the NerdAxe Gamma and Gaia and the BitForge Nano (two EMC2101), the fan and temperature chip is now driven by the emc2101 crate 4.2 (GPTechinno). The board's diode settings stay as they were (Gamma and Gaia 0x24, Nano 0x37), as does the PWM frequency (about 7.8 kHz). Before the switch we reported a division by zero on a zero tach count and two settings it could not make (diode ideality/beta, PWM clock); all three were fixed and released the same day. A later suggestion of ours is in 4.2: the fan speed is written without reading the fan configuration back each time, so a misread byte can no longer change the fan's polarity or PWM clock. Checked on a Gamma, a Gaia and a Nano: the same temperatures and fan speeds as before.
    • Night mode, as the settings now describe it. The settings texts said night mode shows only the clock. It shows the dimmed clock screen instead of the pages: on the colour displays the time with date, hashrate and temperature, on the OLED its clock slide. Corrected in all eight languages.
    • Network page: which changes need a restart. The note above the network settings said every change takes effect after a restart. It now says that Wi-Fi, hostname, USB address and NTP need a restart, while the IPv6 switch and the time zone apply at once. Changed in all eight languages.

    What is fixed.

    • IPv6 after the setup hotspot. When the setup hotspot opened or closed, the next Wi-Fi connection skipped the IPv6 start, and the miner stayed on IPv4 until the link dropped for another reason. It now starts IPv6 again with every new connection.
    • No extra second with IPv6 off. With the IPv6 switch off, every Wi-Fi connection waited one second for an address that never came.
    • TLS pools: one 10-second budget. Choosing between a pool's IPv6 and IPv4 address and the TLS handshake now share one 10-second budget, with at least 5 seconds always kept for the handshake. Before, each had its own 10 seconds.
    • IPv6 address in the pool card. The "Server" row writes an IPv6 address in brackets, so the port stays readable.
    • EMC2101 boards: the chip is identified first. On the Bitaxe Gamma and Gamma Duo, the NerdAxe Gamma and Gaia and the BitForge Nano, the fan and temperature chip is identified again before anything is written to it, as in v0.1.45 and earlier. With a wrong board choice, nothing is written to another chip at the same address.
    • Nerd boards: no doubled fan speed reading. If setting up the EMC2302 fan chip failed after a warm restart, the displayed fan speed could read twice the real value. Only the reading was wrong; the fans themselves were unaffected. The driver now uses the right range from the start.

    For developers.

    • warpaxe-drivers, MIT OR Apache-2.0. The drivers that follow no other firmware's code now live in crates/drivers under MIT OR Apache-2.0: EMC2302 (rewritten from the datasheet), INA260, TMP1075, PCA9544, SSD1306 with its 5×7 font, the PMBus number formats and the NTC thermistor. The rest of WarpAxe stays GPL-3.0-or-later, including the drivers that partly follow ESP-Miner or NerdOS (TPS546, TPS53647, EMC2103, FXL6408), and the EMC2101 board adapter, whose register code is the emc2101 crate's (MIT OR Apache-2.0).
    • embedded-hal 1.0. All drivers use embedded-hal 1.0's I²C trait instead of WarpAxe's own. The bytes on the bus are unchanged.
    • GitHub mirror. The repository is mirrored at github.com/dvb-projekt/dvb-WarpAxe; issues and pull requests are welcome there. Releases and the devices' online updates still come from git.warppool.org.
    • Reported upstream: ESP-Miner #2106 (BM1373 single-chip address), tps546 #1 and #2, bm13xx-rs #10 (BM1373 notes), emc2101-rs #5, #6 and #7, NerdOS #767.

    Image. About 20 KB larger than v0.1.45 (19,952 bytes): about 12 KB for IPv6, about 5 KB for the emc2101 crate and embedded-hal, the rest for the fixes.

    One image for every supported board: warpaxe.bin, warpaxe.bin.sha256, warpaxe.bin.sig; for the first install warpaxe-factory.bin and web-flasher.tar.gz (checksums in install.sha256).

    Source: git.warppool.org/dvb-projekt/dvb-WarpAxe · Mirror: github.com/dvb-projekt/dvb-WarpAxe

    Downloads