-
WarpAxe v0.1.7
Stablereleased this
2026-09-28 17:47:42 +00:00 | 564 commits to main since this releaseNerdOCTAXE-γ runs. WarpAxe now mines on a NerdOCTAXE-γ (Rev 3.1, 6-phase TPS53667) next to the Bitaxe Gamma and the NerdQAxe++. The 6-phase regulator is recognised by its own device code (0x01F8; 0.1.6 refused it and left the chips off), the chip temperature carries NerdOS's +10 °C offset so fan target and shutdown act where they did under NerdOS, and the board publishes NerdOS's clock and voltage steps (525–800 MHz, 1120–1260 mV), so tuners build the same ladder as before. At 700 MHz / 1210 mV it ran alongside NerdOS's numbers: about 11.7 TH/s at 213 W, chips 66 °C with the fans at 77 %.
Display glitches fixed on the Nerd boards. Now and then the LCD showed a whole frame in wrong colours, or a moving edge on the right. The frame went to the panel straight from PSRAM, and the DMA came up short while Wi-Fi and the miner used PSRAM too. Frames now go out in 10-row bands through a small buffer in internal RAM, and the next frame waits until the last one has left.
Switching from AxeOS or NerdOS takes more of your settings. Besides Wi-Fi, pools and hostname, the first start now also takes clock and core voltage, fan mode and speeds, the fan target and chip shutdown temperature, the Nerd boards' second fan and the display orientation and screen-off time. Not the fan PID gains: they belong to the stock firmware's own loop. AxeOS 2.15 keeps its pools in a new form (
pool_1…pool_8); WarpAxe now reads that form first, so pools set after AxeOS's own migration are not lost.Also in this release:
- Link the fans (Settings → Fans and temperature, two-fan boards): M1 runs at M2's speed, which follows the chip temperature — for cases where every fan cools the whole board, e.g. on Y-cables.
- Regulator faults are read like AxeOS does (overvoltage, overcurrent, input undervoltage, over-temperature, output off): reported as
power_faultin the API, on the display and in the web UI, and handled like an overheat stop — core voltage off, a new try after 60 s, off for good after the third within an hour. - NerdQAxe++ Rev 7 has a profile now (TPS546 over two voltage domains, from NerdOS) and can be chosen on the first start. It has not run on hardware yet.
- NerdQX Q1373 takes its regulator part from the device code and the phase count from the board strap, as NerdOS does.
- Bitaxe Gamma:
/api/system/asicanswers with AxeOS's clock and voltage choices (it answered 404). - The Save button waits for its save, so a second tap on a phone cannot restart the miner twice.
- The online update shows the install record only for the image it was made for.
- New texts reviewed by native speakers in all eight languages.
One image for every supported board:
warpaxe.bin,warpaxe.bin.sha256,warpaxe.bin.sig; for the first installwarpaxe-factory.binandweb-flasher.tar.gz(checksums ininstall.sha256). -
WarpAxe v0.1.6
Stablereleased this
2026-09-28 11:15:13 +00:00 | 585 commits to main since this releaseFix for v0.1.5 — please update. After an online update to 0.1.5, the miner restarted about once a minute: the update watcher read the new install record from flash on a thread whose stack lives in PSRAM, which the ESP32-S3 does not allow while the flash cache is off. The record is now read once at boot and kept in RAM. Settings were not affected, but between restarts the miner hashed only for a few seconds.
If your miner is in that loop (0.1.5 was the latest release for about 35 minutes on 28 September): right after a restart, open its web UI, go to System and switch off "Check for updates automatically" — the restarts stop at once. Then upload this release's
warpaxe.binunder System (or reinstall with the web flasher at warppool.org/warpaxe, which keeps your settings), and switch the automatic check back on. Don't use the online update from 0.1.5: it runs on the very thread that crashes.Also in this release:
- The miner looks for a new release every hour instead of every 12 hours, so the "Update available" pill in the header shows up within the hour.
- The header no longer cuts off the tabs when the update pill is shown; below 1100 px the tabs take their own row.
One image for every supported board:
warpaxe.bin,warpaxe.bin.sha256,warpaxe.bin.sig; for the first installwarpaxe-factory.binandweb-flasher.tar.gz(checksums ininstall.sha256). -
WarpAxe v0.1.5
Pre-releasereleased this
2026-09-28 10:39:19 +00:00 | 589 commits to main since this release- Swarm page. Every miner on your network in one view — AxeOS, NerdOS, ForgeOS or WarpAxe: the fleet's hashrate, power, J/TH and record difficulty, each miner's share of the hashrate, and a card per miner with a sparkline and its chip and regulator temperatures. Add miners by address or search the local network. Your browser reads each miner directly (every 30 s by default, not while the tab is hidden); this miner only stores the list. Read-only: it never changes or restarts another miner.
- Tabs in the familiar order: Dashboard, Swarm, Network, Pool, Settings, System. Wi-Fi, hostname and time moved to their own Network tab.
- Starfield background from WarpPool behind the web UI.
- Update check: a miner on a test build (e.g. 0.1.5-rc4) is now offered the release of the same number.
- API:
temptargetreports the fan target under ESP-Miner's name, so tuners keep their own target above it. - New texts reviewed by native speakers in all eight languages.
One image for every supported board:
warpaxe.bin,warpaxe.bin.sha256,warpaxe.bin.sig; for the first installwarpaxe-factory.binandweb-flasher.tar.gz(checksums ininstall.sha256). -
WarpAxe v0.1.4
Stablereleased this
2026-09-28 09:13:59 +00:00 | 595 commits to main since this release- Overheat: back on by itself. After an overheat stop the chips start again once chip and regulator are 10 °C below their limits and at least 60 s have passed; after a lost temperature sensor only with real readings back. The third stop within an hour stays off until it is cleared by hand. The API reports
overheatTripsandoverheatCause(hot or sensor), so a tuner can step the clock down instead of running the same point into the next stop. - Wi-Fi setup hotspot. With no network in the settings, or none reached within three minutes of a start, the miner opens
WarpAxe-XXXX: WPA2, with a ten-digit password made at every start and shown only on the device display. A phone that joins it gets the Wi-Fi setup page by itself; after saving, the miner restarts, joins the network and closes the hotspot. - Download mode button under System, for a reinstall with the web flasher at warppool.org/warpaxe.
- Fixed: chips going silent after some block changes (seen on the 4-chip NerdQAxe++ on Stratum V2): the work of a new block could be retired twice, so the chips idled for up to 30 s.
- Fixed: a wrong password at the hotspot aborted the firmware (an ESP-IDF 5.3 Wi-Fi event unknown to esp-idf-svc 0.51, patched in
vendor/esp-idf-svc). - The log names the address behind every restart, download-mode and overheat-reset request.
- New texts reviewed by native speakers in all eight UI languages and the six display languages.
One image for every supported board:
warpaxe.bin,warpaxe.bin.sha256,warpaxe.bin.sig; for the first installwarpaxe-factory.binandweb-flasher.tar.gz(checksums ininstall.sha256). - Overheat: back on by itself. After an overheat stop the chips start again once chip and regulator are 10 °C below their limits and at least 60 s have passed; after a lost temperature sensor only with real readings back. The third stop within an hour stays off until it is cleared by hand. The API reports
-
WarpAxe v0.1.3
Stablereleased this
2026-09-27 19:21:39 +00:00 | 604 commits to main since this release- Stratum V2 per pool (main and fallback): encrypted Noise connection, the pool's certificate checked against its authority key (optional "require pool authentication"). Stratum V1 with or without TLS stays available.
- Signed releases: the online update checks a BIP-340 signature over the image (
warpaxe.bin.sig) against the key built into the firmware; a bad signature stops the install. This is the first signed release. - TLS memory: mbedTLS now allocates from PSRAM, so a certificate check no longer fails for want of internal RAM after long mining on TLS; update downloads are tried up to three times.
- New texts reviewed by native speakers in all eight UI languages.
One image for every supported board:
warpaxe.bin,warpaxe.bin.sha256,warpaxe.bin.sig. -
WarpAxe v0.1.2
Stablereleased this
2026-09-27 17:45:54 +00:00 | 609 commits to main since this release- Eight languages in the web UI (English, German, Spanish, French, Italian, Brazilian Portuguese, Japanese, Chinese), six on the device display (Japanese and Chinese show English there). Every translation was reviewed by a native speaker.
- First start without a board configured: WarpAxe takes Wi-Fi, pools and hostname from the previous AxeOS/NerdOS settings, then finds the board from what AxeOS stored or from the chips on the I2C bus (read-only). A Bitaxe Gamma is taken at once; NerdQAxe++/NerdOctaxe, NerdQX and NerdAxe ask once in the web UI, with the chips off until then. A NerdQAxe++ Rev 7 is named as not supported yet.
- The log names the address that starts an update, an upload or an update check.
- A dash instead of 0 until the first hashrate estimate.
- Fix: the power card showed "current" as a label instead of the current in amperes.
One image for every supported board:
warpaxe.binandwarpaxe.bin.sha256. -
WarpAxe v0.1.1
Stablereleased this
2026-09-27 16:48:58 +00:00 | 615 commits to main since this releaseSame code as v0.1.0; the version number is the change. v0.1.1 is the first release a miner fetches itself through the online update (System → Online update → Install), to prove the path end to end: download, SHA-256 check, flashing, restart.
-
WarpAxe v0.1.0
Stablereleased this
2026-09-27 16:35:37 +00:00 | 616 commits to main since this releaseFirst public WarpAxe firmware for the Bitaxe Gamma (BM1370) and the NerdQAxe++ (4x BM1370).
- Stratum V1 with fallback pool, optional TLS (certificate checked against the built-in CA bundle)
- AxeOS/NerdOS-compatible API, works with WarpTune
- Web UI with dashboard, 1 h / 3 h history, pool, settings (?oc for free clock/voltage and expert settings), maintenance, live log
- Device display: cockpit and four pages on the NerdQAxe++ LCD, rotation on the Gamma OLED, animated special screens (block found, overheat, chips off, firmware update)
- Online update from git.warppool.org, SHA-256 verified; installing is always a click
One image for every supported board:
warpaxe.bin(app image, for the web UI's update orPOST /api/system/OTA),warpaxe.bin.sha256.